Driver for the Xerox XPRESS Plotter

Sending a Test Plot File

We assume that you will configure Artwork's GDSPLOT to create RTL output and that you wish to get plots. express_plot will read the RTL file and stream out data directly to the Express plotter. To test this last function you can use a small RTL file called colors.rtl that is provided in the release. You can easily exercise different plotting qualities and rolls by using the appropriate command line options.

	./xpress_plot /dev/xpress0 rtl colors.rtl -quality:4 -papersize:a0

	./xpress_plot /dev/xpress0 rtl colors.rtl -quality:4 -roll:1

	./xpress_plot /dev/xpress0 rtl colors.rtl -quality:8 -papersize:a1

	./xpress_plot /dev/xpress0 rtl colors.rtl -roll:2

	./xpress_plot /dev/xpress0 rtl colors.rtl 

The first two lines are equivalent, i.e. the roll selection can be made via the -papersize or -roll command line options. The next two lines differ only by the quality printing mode, specified by the -quality command line option; the default quality is 4. The different print qualities are:


���� Quality�� DPI������� Remarks
������ 1������ 360������� uni-directional draft
������ 2������ 360������� bi-directional draft
������ 3������ 360������� uni-directional std
������ 4������ 360������� bi-directional std
������ 5������ 360������� uni-directional 1/2 interlace
������ 6������ 360������� bi-directional 1/2 interlace
������ 7������ 360������� uni-directional 1/4 interlace
������ 8������ 360������� bi-directional 1/4 interlace
������ 9������ 720������� uni-directional hires 1/2 interlace
����� 10������ 720������� bi-directional hires 1/2 interlace
����� 11������ 720������� uni-directional hires 1/4 interlace
����� 12������ 720������� bi-directional hires 1/4 interlace

express_plot Command Line Options

usage:  xpress_plot: [device] [command]

��� �����

device is the full path name of device i.e. /dev/express0 ��� �����

command is one of the following:

��� 1.��� open - just open & close
��� 
��� 2.��� stop - stop printing
��� 
��� 3.��� sense - send the SCSI 'sense' command
��� 
��� 4.��� monotest dx dy (inches) [other_args]
��� 
��� 5.��� colortest dx dy (inches) [other_args]
��� 
��� 6.��� obsolete
��� 
��� 7.��� rtl rtl_file [other_args]

          where other_args is one of
��� 
������������� -busy:T����������� T is 0 - 60 minutes (default 10)
������������� -quality:Q�������� Q is 1 - 12
������������� -roll:R����������� R is 1 - 4 or auto
������������� -papersize:size	size is a0, a1, a3, a0r, auto
��� 
��������� if rtl_file is '-' then stdin is assumed
��� 
��� 8.��� test paper patternid - generate test print
��� 
���������������������� paper is "a0" or "a1"
�����������������������patternid is 1 - 8
��� 
��� 9.��� roll paper - select roll
��� 
���������������������� paper is "a0" or "a1"
��� 
��� 10.��� cut paper - cut paper roll at current position
��� 
���������������������� paper is "a0" or "a1"
��� 
��� 11.��� feed paper amount - feed paper roll amount inches
��� 
�����������������������paper is "a0" or "a1"
��� 
��� 12.��� inquire info - inquire about info (hex value), one of
��� 
���������������������� 0x00 vendor info
�����������������������0xc0 roll selection
�����������������������0xc1 roll info
�����������������������0xc2 engine status
�����������������������0xc3 interface status
�����������������������0xc4 engine error status
�����������������������0xc5 engine busy status
�����������������������0xc5 engine warning status
�����������������������0xcf machine id
��� 
��� 13.��� errlev [lev] - Set the error reporting level
��� 
��� 14.��� tur - send the SCSI 'test unit ready'command


Page   |    1    |    2    |    3    |    4    |    5    |    6    |    7    |    8    |



Back to FAQ Page Artwork Home